Sheet Metal & Metal Roofing in Southwest Florida
Custom in-house sheet metal fabrication and standing seam metal roofing for Southwest Florida's commercial buildings and high-end residential properties - engineered to take the sun, wind and salt air.
Metal worked the way the building needs it
Sheet metal is where a good roof becomes a watertight one. Edges, valleys, parapet caps, scuppers, counter-flashing - the details that decide whether a roof lasts 10 years or 40 - all start as flat metal. At CFS, we fabricate those details to spec rather than forcing a stock part to fit, so every transition on your roof is made for that exact building.
For more than 40 years, our crews have detailed sheet metal across Fort Myers, Naples, Sarasota and the wider Southwest Florida market - on everything from single-family estates to institutional and commercial campuses. Sheet metal is a craft, and it's one we keep in-house under Florida roofing license CCC1325562. It backs every roofing service we offer, from commercial flat roofs to tile and shingle re-roofs.
- Fabricated to the drawing, not retrofitted from a catalog part - clean profiles, tight seams.
- Color-matched finishes in Galvalume, aluminum and pre-finished steel to match the roof and trim package.
- One accountable contractor - the team fabricating the metal is the team installing the roof.
Metal roofing built for the long haul
A properly installed standing seam metal roof is one of the most durable systems you can put on a Southwest Florida building. Concealed fasteners, raised interlocking seams and continuous panels mean there are no exposed screws to back out and no shingles to lift - just a clean, sealed surface engineered to shed water and stand up to high-wind events.
- Concealed-fastener panels with no exposed penetrations to corrode or loosen over time.
- High-wind ready profiles suited to Florida's coastal building demands and storm exposure.
- Reflective finishes that cut heat gain under the SWFL sun and ease the load on AC systems.
- Decades of service life with minimal upkeep - a fit for commercial roofs and estate homes alike.
The details where leaks start - sealed
Flashing & Counter-Flashing
Wall, curb, chimney, skylight and penetration flashing fabricated to seal every transition on the roof - the joints stock parts never quite fit.
Edge Metal & Coping
Drip edge, fascia, gravel stop and parapet coping caps that finish the perimeter cleanly and lock the membrane or panel down at the edge.
Valleys, Scuppers & Gutters
Custom valley metal, through-wall scuppers, conductor heads and metal gutter work that moves SWFL's heavy rain off the roof fast.
The full metal kit for your roof
The unglamorous parts of a roof are where leaks start. We fabricate the complete kit of metal details so water has nowhere to get in - matched to your roof system, commercial or residential.
Roof-to-Wall Transitions
Headwall, sidewall and step flashing detailed for the way your roof actually meets the structure - critical on additions and mixed-slope roofs.
Curbs & Equipment Penetrations
Metal pitch pans, pipe boots and curb flashing for HVAC units, vents and rooftop equipment on commercial and industrial buildings.
Custom & Architectural Metal
One-off profiles, decorative trim and color-matched accents fabricated to the architect's intent on high-end residential and institutional projects.
Engineered for Southwest Florida
Metal earns its keep in this climate. Salt air, UV, summer downpours and hurricane-season wind are hard on a roof, and they punish weak details first. We fabricate and install with that reality in mind - the right alloys and finishes for coastal exposure, sealed seams, and flashing detailed so nothing relies on caulk alone to stay watertight. Once the roof is on, our Roof Guard maintenance program keeps those metal details inspected and re-sealed before a small gap becomes an interior leak.
Whether it's a new standing seam roof on a Naples estate, the metal package on a Fort Myers commercial campus, or replacement edge metal and flashing on an existing building, CFS is NRCA ProCertified and manufacturer-certified, and fully licensed and insured in Florida under CCC1325562. We fabricate and install across Lee, Collier and Charlotte counties and Sarasota - see our full service area - and if you're chasing an active leak, we can get a crew out for same-day storm response to assess and protect the building while the permanent repair is scoped. Contact CFS to spec the metal for your roof.
